PFERD-旋转锉刀齿型

公开频道 / 说明文章

84 视图
0 喜爱
0 0
PFERD合金旋转锉刀(磨头)各种齿形应用

分享到社交网络

分享链接

使用永久链接在社交媒体中分享

与朋友分享

登录 发送此 document 通过电子邮件!

嵌入你的网页

选择页面开始

1. 1 cut (C according to DIN 8033) ■ Machining of non-ferrous metals, steel and cast iron. ■ High stock removal. 3 cut (MY according to DIN 8033) ■ Machining of steel, cast iron, stainless steel (INOX), nickel-based alloys and titanium alloys. ■ High stock removal. ■ Good surface. 3 PLUS cut (MX according to DIN 8033) ■ Similar to 3 cut, but with cross cut. ■ Machining of steel, cast iron, stainless steel (INOX), nickel-based alloys and titanium alloys. ■ High stock removal. 4 cut (MX according to DIN 8033) ■ Machining of stainless steel (INOX), steel and high-temperature-resistant materials such as nickel-based and cobalt-based alloys. ■ High stock removal with short chips. ■ Good surface. 5 cut (F according to DIN 8033) ■ Fine machining of steel, cast iron, stain - less steel (INOX) and high-temperature- resistant materials such as nickel-based and cobalt-based alloys. ■ Good surface. TC burrs PFERD cuts for high-performance applications ALLROUND cut ■ High stock removal rate on key materials such as steel, cast steel, stainless steel (INOX), non-ferrous metals and cast iron. ■ Similar to the 3 PLUS cut but with a sig - nificantly higher stock removal rate. STEEL cut ■ Extremely high stock removal rate on steel and cast steel. ■ Smooth milling. ■ Reduced vibration and less noise. INOX cut ■ Extremely high stock removal rate on all austenitic, rust and acid-resistant steels, stainless steel (INOX) and soft titanium alloys. ■ Significantly reduced vibration and less noise. ALU cut ■ High stock removal rate on aluminium and aluminium alloys, non-ferrous metals and plastics. ■ Smooth milling. NON-FERROUS cut ■ High stock removal rate on non-ferrous metals, brass, copper, plastics and fibre- reinforced plastics. ■ Suitable for universal use. CAST cut ■ Extremely high stock removal rate on cast iron. ■ Smooth milling. ■ Reduced vibration and less noise. TITANIUM cut ■ Outstanding stock removal rate and service life on hard titanium alloys. ■ Significantly increased aggressiveness, large chips and very good chip removal. ■ Reduced vibration and less noise. EDGE cut ■ Creates exact edge shapes – with either 30° or 45° chamfering or a defined radius of 3.0 mm. ■ Safe and comfortable to guide. PLAST cut ■ Trimming and contour milling of work - pieces made from less hard glass and carbon-fibre-reinforced duroplastics (GRP and CRP with ≤ 40 % fibre content) and fibre-reinforced thermoplastics. ■ Minimized delamination and fraying through straight cut. ■ Highly suitable for use on machines and on robots. ■ Reduced vibration and less noise. FVK cut ■ Trimming and contour milling of work - pieces made from hard glass and carbon- fibre-reinforced duroplastics (also GRP and CRP > 40 %). FVKS cut ■ Similar to the FVK cut. ■ Smooth milling. TOUGH cut ■ High stock removal rate on cast iron, steel < 54 HRC. ■ Extremely resistant to impacts. ■ Also suitable for use with high surface contact angles > 1/3 and under impact loads. TOUGH-S cut ■ High stock removal rate on cast iron, steel < 54 HRC. ■ Similar to the TOUGH cut, but with smoother milling and shorter chips. ■ Extremely resistant to impacts. ■ Also suitable for use with high surface contact angles > 1/3 and under impact loads. MICRO cut ■ Good stock removal on almost all materials < 68 HRC. ■ High surface quality. ■ Reduced vibration and less noise. HICOAT coatings ■ In general, all PFERD tungsten carbide burrs are also available with HICOAT coatings. ■ Improved anti-adhesion characteristics. ■ Effective chip discharge. ■ Lower thermal loads. ■ Increased service life. ■ Also suitable for use at higher cutting speeds when compared with uncoated burrs. Products made to order If you cannot find the solution for your particular application in our extensive catalogue range, we produce PFERD premium-quality burrs, tailor-made to meet the requirements of your job. Further information on PFERD products made to order can be found on page 100. 9 2 2 Catalogue Page

视图

  • 84 全部视图
  • 62 网站视图
  • 22 内嵌视图

动作

  • 0 社交分享
  • 0
  • 0
  • 0 评论

分享数

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn领英
  • 0 Google+

嵌入 2

  • 1 www.shcxco.com:8069
  • 1 shcxco.com
    没有介绍。